Rag 'n' Bone Brown is an online video channel documenting woodworking, restoration, DIY and upcycling projects using mainly salvaged wood and reclaimed materials by Keith Brown, Maker Of Things. Videos range from build projects like furniture builds and restorations, workshop projects, home & garden & pet projects to vlogs, tool reviews and influencer interviews. Based in Norwich in the UK, the channel began in 2015 on YouTube.

Making A Cat House For Two Using Scraps Of Wood

In this video, my brother Alan visits my workshop bringing with him some scraps of sheet materials found in his shed - some pieces of various sizes of MDF, ply and chipboard.

Alan wanted a cat house for his two cats George & Jasper, and he already had an idea for the design he wanted, so we first did a quick drawing in SketchUp to figure out how to make best use of the materials that we had to create that design.

Making A Treasure Chest Blanket Box / Ottoman (part 2 of 2)

In this video I start by finishing off the arcs for the lid that I started making in the previous video.  I cut one of them in half on the bandsaw to give me 2x thinner ones (for each end) and one wide one (for the middle of the lid).

I needed to cut a rebate joint in to one side of each end arc and both sides of the central arc.  I did this by putting my trim router upside down in the vise to use as a makeshift router table - which worked well.

Then I glued and clamped the arcs in place.

Making A Treasure Chest Blanket Box / Ottoman (part 1 of 2)

In this video I start making a blanket box in the style of a treasure chest using a donated slab of sapele and some pieces of pine from my workshop.

I started by drawing up a 3D model of what I wanted to make in SketchUp.  

Then I ripped the sapele in to 40mm thick strips, thickness planed them so that they were 40mm x 40mm, and then cut a 12mm x 12mm rebate joint along the full length of each piece on the tablesaw.

Finishing The New Workshop Layout - Workshop Re-Model Episode 8

Last in a short series about re-modelling my small workshop space.

In this video I make a simple box out of some salvaged OSB to store wood.  Simple butt joints, glued and screwed, and I added some castors to the bottom just because I had a spare set which will be useful if I ever need to move it around.

Mitre Station Support, Clamp Storage & Tool Wall - Workshop Re-Model Episode 7

In this video I make a simple unit to support material at the right hand side of my mitre station while I make cuts that also holds some of my clamps too, and I start my first of two new tool walls.
 
I used some scrap blockboard and melamine to make a simple unit mounted on castors which sits about 1cm below the height of the mitre saw’s base so that when I cut material, the offcut doesn’t fall on to the floor of the workshop.
 
I made a simple rack inside the unit to hold my F clamps by cutting some slots in to another piece

New Mitre Station (part 3 of 3) - Workshop Re-Model Episode 6

In part 3 I begin by making a new fence for the mitresaw.  Originally I was going to make one using wood, but while I was in my local DIY shop I stumbled upon some lengths of aluminium angle which were relatively inexpensive and it occurred to me that it would be worth using that instead as it is perfectly straight.  
 
I decided to fit this not only to the worktop of the mitrestation, but also to the saw itself to replace the existing mitre saw fence.

The New Mitre Station (part 2 of 3) - Workshop Re-Model Episode 5

In part 2 of the mitre station build, I started by fitting some structural supports/spacers to the mitresaw stand.  These would make the structure more rigid and also ensure that the space between the two panels would be evenly spaced so that I could later fit a drawer in the space.
 
Next I made a hood for the mitresaw to help contain any dust that my shop vac doesn’t catch.  I used some salvaged blockboard to make the hood, and another piece of white 1 inch thick melamine for the top.

The New Mitre Station (part 1 of 3) - Workshop Re-Model Episode 4

In this video I start making a new mitre station for my workshop to create space in the corner for a wood storage bin, and also to make it a little slimmer so there would be more walkway space.  
 
I dismantled my old mitre station and re-used most of the material for the new one.  
 
I started by screwing a horizontal support piece to the uprights of the workshop walls.

Wood Finishes - A Quick Guide - Varnish / Stain / Oil / Wax / Lacquer / Polyurethane / Shellac

Wood stains, also known as wood dyes are designed to change the colour of wood while leaving the grain still visible.

Mobile Tablesaw Stand for DeWalt DW745 (part 2 of 2) - Workshop Re-Model Episode 3

In this video I make a back panel for the stand out of some low grade packaging plywood.  I did this mainly to stop some of the dust getting in to the bottom section where the shop vac and jigs will be stored, but it will also add rigidity to the stand.

Next I fitted the shop vac hose, using a hole saw drill bit.

I cut some pieces of poplar in to 10mm strips, cut them to length and glued and nailed them to the front edges of the stand mainly to hide the plywood edges for aesthetics.

Pages